Remove all screws, oil threads, and the point of the set screws or threads, beneath the mind of the cap screws.
Insert screws in to the holes that are threaded upon the bushing side, since shown in Physique 2. In sizes where washers are located under the screw head, be certain to use these washers. Please note that there should always become one screw left over that’s not used when eliminating the bushing.
Tighten the screws alternately before bushing is loosened in the hub. If the bushing will not loosen instantly, tap on the hub to assist remove.
When installing or removing a Taper Lock bush, it is imperative that no lubrication be used between your taper. The existence of lubricant on the tapered areas is not desired, as the taper bushing relies on friction to operate efficiently, and lubricants decrease friction. use industry standard Component Numbers to recognize the specifications of each Taper Lock bush or Taper bush.
It is the most successful shaft fixing in the market place today with a full range of both metric 
and imperial sizes in addition to a full range of weld-on hubs, bolt-on hubs and hub adaptors.
Simple installation and removal
Equal to a shrink-on fit on uniform load applications and therefore eliminating the cost of a key
No costly reboring: complete range of both metric and imperial available
Standard range suits up to 125mm/5″ shafts
Particular 4-hole feature for balanced assemblies
Complete short reach range offered, for compact lightweight assemblies
High grade, close grain iron (GG25) material
Spherodial Graphite (S.G.) iron construction on some sizes to give increase maximum bores
Manufactured from steel to provide convenient methods to secure fan rotors, steel pulleys, plate sprockets, impellers etc. to a shaft.
Shouldered outer diameter permits easy location
A convenient means to secure fan rotors, metal pulleys, plate sprockets, impellers etc to a shaft
Welding not necessary
For use with parallel bore eliminating the cost of drilling, tapping and taper boring
Keyed version also available for heavy duty applications
Installation of a Taper Lock bush, including Martin or Fenner Taper Lock bush parts, is as follows:
Screws ought to be tightened alternately and evenly until all screws are pulled up and the bushing is square into the hub.
The Taper Lock bush needs to be thoroughly cleaned, removing all traces of oil, grease, dirt, and metal filings. Clean the shaft, the bore, the exterior of the bushing, and the bore of the hub where the bush is to be installed into, making sure the bush is taken off the hub, should it currently be installed.
Check the bushing to ensure all surfaces are free from nicks and burrs, and ensure the bushing has no signals of cracking or fatigue. Place the bushing into the hub and match fifty percent holes to make complete holes. It is important to note that the holes need to be matched, not the threads. Each hole will be threaded using one side only.
Oil threads, the point of the established screws or threads, and beneath the head of the cap screws. Then place the screws loosely in to the holes that are threaded on the hub-side
Ensure that the Taper Lock bush is free in the hub, then slide the assembly onto the shaft and locate in the desired position. Insert the correctly sized key into the shaft keyway, ensuring the main element is a press match the shaft keyway. Ensure there can be an air gap between your top of the essential and the bushing keyway slot. This will prevent cracking of the bush. IMPORTANT: Ensure that there is no essential oil or lubricant between the taper externally of the bushing and the taper bore of the hub, to which the bushing is being installed.
Screws should be tightened alternately and evenly until all screws are pulled up and the bushing is square into the hub.
Using a hammer and prevent, or sleeve, against the huge end of the Taper Lock bush will avoid harm to the bushing. Gently tap against the busing to ensure it is seated squarely. The screws are then tightened additional. A torque wrench can be used to tighten the screws additionally and evenly until they are all to the recommended torque setting.
Continue doing this alternate hammering and screw tightening before specified torque is accomplished no longer requires tightening following hammering. IMPORTANT: After a period of running under normal conditions, it is suggested that the application form be reviewed to guarantee the torque configurations of the screws are accurate, and don’t need re-tightening.
Fill up the holes that are not used with grease or silicone sealant to prevent them from filling with dirt and/or rust.
Removal of a Taper Lock bush, including Martin or Fenner Taper Lock bush elements, is as follows: